Suburban Tool Fly Cutter Body and 2 Bar Set
November 23, 2018
If your wondering why your getting chatter and poor surface finish with your standard fly cutter you have to look at its construction. Most adjustable fly cutters use a 1/2 tool bit that was designed to be used on a lathe or in a boring bar. Hang that 1/2 tool bit out a little to get a larger width of cut and you create chatter, it’s not rigid enough. There are other obvious factors that can cause a poor finish such as sloppy spindle bearings in the machine, an out of tram head, or sloppy ways and or gibs. Another issue is with how the cutter is attached to the machine. A big cylindrical disk is very rigid but the 1/2″ or 3/4″ or even 1 shaft is not and the stiffness or rigidity of the tool just makes the shaft flex more creating chatter and poor finish. Collet type holders should never be used with a fly cutter and most end mill holders are too long and create too much leverage because they hang down too far. For best results the cutting edge of a fly cutter should be as close to the machines spindle as possible. Brand new fly cutter body and 2 bar set. Comes with one 5″ and one 7.5″ bar. All bars are 1 thick. Maximum cut diameter 10.625″ with the 7.5″ bar and minimum 5.875″ with the 5″ bar and with both bars, covers every size in between. Comes complete with 2 TNMG 432 inserts, 4 insert screws (1 on each bar and 2 extras) and 1 1/2-20 socket head cap screw to mount the cutter body to your shell mill / face mill holder. Cutter body fits on a 1″ shell mill arbor with 3/8″ key. See links at the bottom of this listing for Arbors and inserts that work with this tool. Can be used on CNC Mill, Boring Mill, Bridgeport, Floor Mill, Vertical Mill, Horizontal Mill etc. Can be used to cut a wide variety of materials from aluminum and plastics to tool steels. Uses TNMG 432 series un-coated inserts for milling cast iron, aluminum and plastic and TNMG 432 tin coated inserts for steel and tool steels. Cut depths of up to. 030 in steel and. 080 + in aluminum and plastics. Can also be used to rough workpieces and remove scale, when a large surface area needs to be covered. An excellent tool for weldments and flimsy hard to hold workpieces. Works great for facing or skimming cylinder heads and decking engine blocks. When using for skimming cylinder heads or decking an engine block this tool is the choice to get it done right the first time. Using a scrap practice head made of the same material you intend to cut, is recommended to help you to fine tune your feed and spindle speed rates for your machine. Once the rpm and feed rates have been established one or 2 light passes will get the job done fast. A single TNMG insert should last through many projects. In many cases this tool will eliminate the need for surface or Blanchard grinding, and is great for 1 pass per side squaring of workpieces. The bar is adjustable and reversible and can be used to cut inside of clevises and the underside of overhanging work pieces. If bar is reversed the spindle must be run in reverse (ccw) Can be used to finish bore the id of large diameter holes from 5.875″ to 10.625″ with this 2 bar set. All of our fly cutter products including the bars and cutter bodies are plated with clear zinc for corrosion resistance and are cryogenically treated (prior to manufacturing) for stability and to reduce vibration. More Fly Cutter Videos. R8 Arbor for this Cutter. Cat 40 Arbor for this Cutter. Inserts for this Cutter. Link to Feed and Speed Recommendations and Safety Sheet. We sincerely hope that you can leave us a. The item “Suburban Tool Fly Cutter Body and 2 Bar Set” is in sale since Thursday, June 20, 2013. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\CNC & Metalworking Supplies\Other CNC & Metalworking Supplies”. The seller is “mvpmachine” and is located in Fraser, Michigan. This item can be shipped worldwide.
- Brand: Suburban Tool
- Model: Suburban Tool Fly Cutter Set
- MPN: FCS-SET0507
- Quantity: 1
- Country/Region of Manufacture: United States