https://cuttersettool.com Sat, 02 May 2026 02:15:57 +0000 en-US hourly 1 https://cuttersettool.com/2025/12/30/malco-hc1-hc2-hole-cutter-main-video/ https://cuttersettool.com/2025/12/30/malco-hc1-hc2-hole-cutter-main-video/#comments Tue, 30 Dec 2025 22:25:32 +0000 https://cuttersettool.com/2025/12/30/malco-hc1-hc2-hole-cutter-main-video/ ]]> https://cuttersettool.com/2025/12/30/malco-hc1-hc2-hole-cutter-main-video/feed/ 0 https://cuttersettool.com/2024/11/20/allpax-heavy-duty-gasket-cutter-kit-instructional-video/ https://cuttersettool.com/2024/11/20/allpax-heavy-duty-gasket-cutter-kit-instructional-video/#comments Thu, 21 Nov 2024 03:37:56 +0000 https://cuttersettool.com/2024/11/20/allpax-heavy-duty-gasket-cutter-kit-instructional-video/ ]]> https://cuttersettool.com/2024/11/20/allpax-heavy-duty-gasket-cutter-kit-instructional-video/feed/ 0 https://cuttersettool.com/2024/09/08/suburban-tool-fly-cutter-body-and-2-bar-set-5-and-7-5-bars-see-video-2/ https://cuttersettool.com/2024/09/08/suburban-tool-fly-cutter-body-and-2-bar-set-5-and-7-5-bars-see-video-2/#comments Sun, 08 Sep 2024 05:58:33 +0000 https://cuttersettool.com/2024/09/08/suburban-tool-fly-cutter-body-and-2-bar-set-5-and-7-5-bars-see-video-2/







If your wondering why your getting chatter and poor surface finish with your standard fly cutter you have to look at its construction. Most adjustable fly cutters use a 1/2 tool bit that was designed to be used on a lathe or in a boring bar. Hang that 1/2 tool bit out a little to get a larger width of cut and you create chatter, it’s not rigid enough. There are other obvious factors that can cause a poor finish such as sloppy spindle bearings in the machine, an out of tram head, or sloppy ways and or gibs. Another issue is with how the cutter is attached to the machine. A big cylindrical disk is very rigid but the 1/2″ or 3/4″ or even 1 shaft is not and the stiffness or rigidity of the tool just makes the shaft flex more creating chatter and poor finish. Collet type holders should never be used with a fly cutter and most end mill holders are too long and create too much leverage because they hang down too far. For best results the cutting edge of a fly cutter should be as close to the machines spindle as possible. Brand new fly cutter body and 2 bar set. Comes with one 5″ and one 7.5″ bar. All bars are 1 thick. Maximum cut diameter 10.625″ with the 7.5″ bar and minimum 5.875″ with the 5″ bar and with both bars, covers every size in between. Comes complete with 2 TNMG 432 inserts, 4 insert screws (1 on each bar and 2 extras) and 1 1/2-20 socket head cap screw to mount the cutter body to your shell mill / face mill holder. Cutter body fits on a 1″ shell mill arbor with 3/8″ key. See links at the bottom of this listing for Arbors and inserts that work with this tool. Can be used on CNC Mill, Boring Mill, Bridgeport, Floor Mill, Vertical Mill, Horizontal Mill etc. Can be used to cut a wide variety of materials from aluminum and plastics to tool steels. Uses TNMG 432 series un-coated inserts for milling cast iron, aluminum and plastic and TNMG 432 tin coated inserts for steel and tool steels. Cut depths of up to. 030 in steel and. 080 + in aluminum and plastics. Can also be used to rough workpieces and remove scale, when a large surface area needs to be covered. An excellent tool for weldments and flimsy hard to hold workpieces. Works great for facing or skimming cylinder heads and decking engine blocks. When using for skimming cylinder heads or decking an engine block this tool is the choice to get it done right the first time. Using a scrap practice head made of the same material you intend to cut, is recommended to help you to fine tune your feed and spindle speed rates for your machine. Once the rpm and feed rates have been established one or 2 light passes will get the job done fast. A single TNMG insert should last through many projects. In many cases this tool will eliminate the need for surface or Blanchard grinding, and is great for 1 pass per side squaring of workpieces. The bar is adjustable and reversible and can be used to cut inside of clevises and the underside of overhanging work pieces. If bar is reversed the spindle must be run in reverse (ccw) Can be used to finish bore the id of large diameter holes from 5.875″ to 10.625″ with this 2 bar set. All of our fly cutter products including the bars and cutter bodies are plated with clear zinc for corrosion resistance and are cryogenically treated (prior to manufacturing) for stability and to reduce vibration. We sincerely hope that you can leave us a. Suburban Tool Fly Cutter as good as Surface Grinder?

]]> https://cuttersettool.com/2024/09/08/suburban-tool-fly-cutter-body-and-2-bar-set-5-and-7-5-bars-see-video-2/feed/ 0 https://cuttersettool.com/2024/08/02/how-to-make-rhinestone-template-with-cricut-tutorial-video-cricutmaker-designspace-diycrafts/ https://cuttersettool.com/2024/08/02/how-to-make-rhinestone-template-with-cricut-tutorial-video-cricutmaker-designspace-diycrafts/#comments Fri, 02 Aug 2024 11:01:17 +0000 https://cuttersettool.com/2024/08/02/how-to-make-rhinestone-template-with-cricut-tutorial-video-cricutmaker-designspace-diycrafts/ ]]> https://cuttersettool.com/2024/08/02/how-to-make-rhinestone-template-with-cricut-tutorial-video-cricutmaker-designspace-diycrafts/feed/ 0 https://cuttersettool.com/2024/07/05/roberts-13in-multi-floor-cutter-10-63-product-video-eng/ https://cuttersettool.com/2024/07/05/roberts-13in-multi-floor-cutter-10-63-product-video-eng/#comments Fri, 05 Jul 2024 23:09:55 +0000 https://cuttersettool.com/2024/07/05/roberts-13in-multi-floor-cutter-10-63-product-video-eng/ ]]> https://cuttersettool.com/2024/07/05/roberts-13in-multi-floor-cutter-10-63-product-video-eng/feed/ 0 https://cuttersettool.com/2023/09/23/suburban-tool-fly-cutter-and-3-bar-set-for-bridgeport-mill-cnc-see-video-2/ https://cuttersettool.com/2023/09/23/suburban-tool-fly-cutter-and-3-bar-set-for-bridgeport-mill-cnc-see-video-2/#comments Sat, 23 Sep 2023 16:12:06 +0000 https://cuttersettool.com/2023/09/23/suburban-tool-fly-cutter-and-3-bar-set-for-bridgeport-mill-cnc-see-video-2/






I f your wondering why your getting chatter and poor surface finish with your standard fly cutter you have to look at its construction. Most adjustable fly cutters use a 1/2 tool bit that was designed to be used on a lathe or in a boring bar. Hang that 1/2 tool bit out a little to get a larger width of cut and you create chatter, it’s not rigid enough. There are other obvious factors that can cause a poor finish such as sloppy spindle bearings in the machine, an out of tram head, or sloppy ways and or gibs. Another issue is with how the cutter is attached to the machine. A big cylindrical disk is very rigid but the 1/2″ or 3/4″ or even 1 shaft is not and the stiffness or rigidity of the tool just makes the shaft flex more creating chatter and poor finish. Collet type holders should never be used with a fly cutter and most end mill holders are too long and create too much leverage because they hang down too far. For best results the cutting edge of a fly cutter should be as close to the machines spindle as possible. Brand new fly cutter body and 3 bar set. Comes with one 5″, one 7.5″, and one 11 long bar. All bars are 1 thick. Maximum cut diameter 18.25″ with the 11″ bar and minimum 6.06″ with the 5″ bar and with all 3 bars, covers every size in between. Comes complete with 3 TNMG 432 inserts, 6 insert screws (1 on each bar and 3 extras) and 1 1/2-20 socket head cap screw to mount the cutter body to your shell mill / face mill holder. Cutter body fits 1″ boss shell mill arbor with 3/8″ key. See links below for R-8 and Cat40 arbors and inserts that fit this tool. Can be used on CNC Mill, Boring Mill, Bridgeport, Floor Mill, Vertical Mill, Horizontal Mill etc. Uses TNMG 432 series un-coated inserts for milling cast iron, aluminum and plastic and TNMG 432 tin coated inserts for steel and tool steels. Cut depths of up to. 030 in steel and. 080 + in aluminum and plastics. Can also be used to rough workpieces and remove scale, when a large surface area needs to be covered. An excellent tool for weldments and flimsy hard to hold workpieces. Works great for facing or skimming cylinder heads and decking engine blocks. When using for skimming cylinder heads or decking an engine block this tool is the choice to get it done right the first time. Using a scrap practice head made of the same material you intend to cut, is recommended to help you to fine tune your feed and spindle speed rates for your machine. Once the rpm and feed rates have been established one or 2 light passes will get the job done fast. A single TNMG insert should last through many projects. In many cases this tool will eliminate the need for surface or Blanchard grinding, and is great for 1 pass per side squaring of workpieces. The bar is adjustable and reversible and can be used to cut inside of clevises and the underside of overhanging work pieces. If bar is reversed the spindle must be run in reverse (ccw) Can be used to finish bore the id of large diameter holes from 6.06″ to 18.25″ with this three bar set. All of our fly cutter products including the bars and cutter bodies are plated with clear zinc for corrosion resistance and are cryogenically treated (prior to manufacturing) for stability and to reduce vibration. Visit our eB ay Store to see our other Manufacturing Products. We sincerely hope that you can leave us a. Suburban Tool Big Fly Cutter for a Bridgeport Mill – YouTube.

]]> https://cuttersettool.com/2023/09/23/suburban-tool-fly-cutter-and-3-bar-set-for-bridgeport-mill-cnc-see-video-2/feed/ 0 https://cuttersettool.com/2022/11/06/huge-fly-cutter-for-bridgeport-mill-cnc-mill-and-boring-mill-see-video/ https://cuttersettool.com/2022/11/06/huge-fly-cutter-for-bridgeport-mill-cnc-mill-and-boring-mill-see-video/#comments Sun, 06 Nov 2022 09:47:28 +0000 https://cuttersettool.com/2022/11/06/huge-fly-cutter-for-bridgeport-mill-cnc-mill-and-boring-mill-see-video/






Brand new fly cutter body and 7.5 bar set. Comes with one 7.5″ x1″ thick adjustable bar. Minimum cut diameter 7.75″ maximum cut diameter 10.625″ Comes complete with 1 TIN Coated TNMG 432 carbide insert, 2 insert screws and 1 1/2-20 socket head cap screw to mount the cutter body to your shell mill / face mill holder. Cutter body fits on a 1″ shell mill arbor with 3/8″ key. Can be used on CNC Mill, Boring Mill, Bridgeport, Floor Mill, Vertical Mill, Horizontal Mill etc. Can be used to cut a wide variety of materials from aluminum and plastics to tool steels. Uses TNMG 432 series un-coated inserts for milling cast iron, aluminum and plastic and TNMG 432 TIN coated inserts for steel and tool steels. Cut depths of up to. 030 in steel and. 080 + in aluminum and plastics. Can also be used to rough workpieces and remove scale, when a large surface area needs to be covered. An excellent tool for weldments and flimsy hard to hold workpieces. Works great for facing or skimming cylinder heads and decking engine blocks. When using for skimming cylinder heads or decking an engine block this tool is the choice to get it done right the first time. Using a scrap practice head made of the same material you intend to cut, is recommended to help you to fine tune your feed and spindle speed rates for your machine. Once the rpm and feed rates have been established one or 2 light passes will get the job done fast. A single TNMG insert should last through many projects. In many cases this tool will eliminate the need for surface or Blanchard grinding, and is great for 1 pass per side squaring of workpieces. The bar is adjustable and reversible and can be used to cut inside of clevises and the underside of overhanging work pieces. If bar is reversed the spindle must be run in reverse (ccw) Can be used to finish bore the id of large diameter holes from 7.69″ to 10.625″. All of our fly cutter products including the bars and cutter bodies are plated with clear zinc for corrosion resistance and are cryogenically treated (prior to manufacturing) for stability and to reduce vibration. We sincerely hope that you can leave us a. Suburban Tool Fly Cutter as good as Surface Grinder? This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Supplies\Milling Cutters”. The seller is “mvpmachine” and is located in this country: US. This item can be shipped worldwide.

• Country/Region of Manufacture: United States
• Cutting/Head Diameter: 10 in
• Mill Cutter Type: Fly Cutter
• Material: Carbide-Tipped
• Quantity: 1
• Model: FCS-SET07
• MPN: FCS-SET07
• Brand: Suburban Tool

]]> https://cuttersettool.com/2022/11/06/huge-fly-cutter-for-bridgeport-mill-cnc-mill-and-boring-mill-see-video/feed/ 0 https://cuttersettool.com/2022/09/11/best-fly-cutter-for-bridgeport-mill-cnc-mill-etc-see-video-7-75-to-10-625-dia/ https://cuttersettool.com/2022/09/11/best-fly-cutter-for-bridgeport-mill-cnc-mill-etc-see-video-7-75-to-10-625-dia/#comments Mon, 12 Sep 2022 01:54:45 +0000 https://cuttersettool.com/2022/09/11/best-fly-cutter-for-bridgeport-mill-cnc-mill-etc-see-video-7-75-to-10-625-dia/






If your wondering why your getting chatter and poor surface finish with your standard fly cutter you have to look at its construction. Most adjustable fly cutters use a 1/2 tool bit that was designed to be used on a lathe or in a boring bar. Hang that 1/2 tool bit out a little to get a larger width of cut and you create chatter, it’s not rigid enough. There are other obvious factors that can cause a poor finish such as sloppy spindle bearings in the machine, an out of tram head, or sloppy ways and or gibs. Another issue is with how the cutter is attached to the machine. A big cylindrical disk is very rigid but the 1/2″ or 3/4″ or even 1 shaft is not and the stiffness or rigidity of the tool just makes the shaft flex more creating chatter and poor finish. Collet type holders should never be used with a fly cutter and most end mill holders are too long and create too much leverage because they hang down too far. For best results the cutting edge of a fly cutter should be as close to the machines spindle as possible. Brand new fly cutter body and 7.5 bar set. Comes with one 7.5″ x1″ thick adjustable bar. Minimum cut diameter 7.75″ maximum cut diameter 10.625″ Comes complete with 1 TIN Coated TNMG 432 carbide insert, 2 insert screws and 1 1/2-20 socket head cap screw to mount the cutter body to your shell mill / face mill holder. Cutter body fits on a 1″ shell mill arbor with 3/8″ key. See links at the bottom of this listing for Arbors and Inserts. Can be used on CNC Mill, Boring Mill, Bridgeport, Floor Mill, Vertical Mill, Horizontal Mill etc. Can be used to cut a wide variety of materials from aluminum and plastics to tool steels. Uses TNMG 432 series un-coated inserts for milling cast iron, aluminum and plastic and TNMG 432 TIN coated inserts for steel and tool steels. Cut depths of up to. 030 in steel and. 080 + in aluminum and plastics. Can also be used to rough workpieces and remove scale, when a large surface area needs to be covered. An excellent tool for weldments and flimsy hard to hold workpieces. Works great for facing or skimming cylinder heads and decking engine blocks. When using for skimming cylinder heads or decking an engine block this tool is the choice to get it done right the first time. Using a scrap practice head made of the same material you intend to cut, is recommended to help you to fine tune your feed and spindle speed rates for your machine. Once the rpm and feed rates have been established one or 2 light passes will get the job done fast. A single TNMG insert should last through many projects. In many cases this tool will eliminate the need for surface or Blanchard grinding, and is great for 1 pass per side squaring of workpieces. The bar is adjustable and reversible and can be used to cut inside of clevises and the underside of overhanging work pieces. If bar is reversed the spindle must be run in reverse (ccw) Can be used to finish bore the id of large diameter holes from 7.69″ to 10.625″. All of our fly cutter products including the bars and cutter bodies are plated with clear zinc for corrosion resistance and are cryogenically treated (prior to manufacturing) for stability and to reduce vibration. We sincerely hope that you can leave us a. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Supplies\Milling Cutters”. The seller is “mvpmachine” and is located in this country: US. This item can be shipped worldwide.

• Country/Region of Manufacture: United States
• Mill Cutter Type: Fly Cutter
• Quantity: 1
• Model: FCS-SET07
• MPN: FCS-SET07
• Brand: Suburban Tool

]]> https://cuttersettool.com/2022/09/11/best-fly-cutter-for-bridgeport-mill-cnc-mill-etc-see-video-7-75-to-10-625-dia/feed/ 0 https://cuttersettool.com/2021/10/27/if-you-love-milwaukee-tools-you-will-hate-this-video-the-future-of-milwaukee-tool-is-uncertain/ https://cuttersettool.com/2021/10/27/if-you-love-milwaukee-tools-you-will-hate-this-video-the-future-of-milwaukee-tool-is-uncertain/#comments Wed, 27 Oct 2021 14:39:15 +0000 http://cuttersettool.com/2021/10/27/if-you-love-milwaukee-tools-you-will-hate-this-video-the-future-of-milwaukee-tool-is-uncertain/ ]]> https://cuttersettool.com/2021/10/27/if-you-love-milwaukee-tools-you-will-hate-this-video-the-future-of-milwaukee-tool-is-uncertain/feed/ 0 https://cuttersettool.com/2020/12/12/suburban-tool-fly-cutter-body-and-2-bar-set-5-and-7-5-bars-see-video/ https://cuttersettool.com/2020/12/12/suburban-tool-fly-cutter-body-and-2-bar-set-5-and-7-5-bars-see-video/#comments Sat, 12 Dec 2020 08:56:55 +0000 http://cuttersettool.com/2020/12/12/suburban-tool-fly-cutter-body-and-2-bar-set-5-and-7-5-bars-see-video/







If your wondering why your getting chatter and poor surface finish with your standard fly cutter you have to look at its construction. Most adjustable fly cutters use a 1/2 tool bit that was designed to be used on a lathe or in a boring bar. Hang that 1/2 tool bit out a little to get a larger width of cut and you create chatter, it’s not rigid enough. There are other obvious factors that can cause a poor finish such as sloppy spindle bearings in the machine, an out of tram head, or sloppy ways and or gibs. Another issue is with how the cutter is attached to the machine. A big cylindrical disk is very rigid but the 1/2″ or 3/4″ or even 1 shaft is not and the stiffness or rigidity of the tool just makes the shaft flex more creating chatter and poor finish. Collet type holders should never be used with a fly cutter and most end mill holders are too long and create too much leverage because they hang down too far. For best results the cutting edge of a fly cutter should be as close to the machines spindle as possible. Brand new fly cutter body and 2 bar set. Comes with one 5″ and one 7.5″ bar. All bars are 1 thick. Maximum cut diameter 10.625″ with the 7.5″ bar and minimum 5.875″ with the 5″ bar and with both bars, covers every size in between. Comes complete with 2 TNMG 432 inserts, 4 insert screws (1 on each bar and 2 extras) and 1 1/2-20 socket head cap screw to mount the cutter body to your shell mill / face mill holder. Cutter body fits on a 1″ shell mill arbor with 3/8″ key. See links at the bottom of this listing for Arbors and inserts that work with this tool. Can be used on CNC Mill, Boring Mill, Bridgeport, Floor Mill, Vertical Mill, Horizontal Mill etc. Can be used to cut a wide variety of materials from aluminum and plastics to tool steels. Uses TNMG 432 series un-coated inserts for milling cast iron, aluminum and plastic and TNMG 432 tin coated inserts for steel and tool steels. Cut depths of up to. 030 in steel and. 080 + in aluminum and plastics. Can also be used to rough workpieces and remove scale, when a large surface area needs to be covered. An excellent tool for weldments and flimsy hard to hold workpieces. Works great for facing or skimming cylinder heads and decking engine blocks. When using for skimming cylinder heads or decking an engine block this tool is the choice to get it done right the first time. Using a scrap practice head made of the same material you intend to cut, is recommended to help you to fine tune your feed and spindle speed rates for your machine. Once the rpm and feed rates have been established one or 2 light passes will get the job done fast. A single TNMG insert should last through many projects. In many cases this tool will eliminate the need for surface or Blanchard grinding, and is great for 1 pass per side squaring of workpieces. The bar is adjustable and reversible and can be used to cut inside of clevises and the underside of overhanging work pieces. If bar is reversed the spindle must be run in reverse (ccw) Can be used to finish bore the id of large diameter holes from 5.875″ to 10.625″ with this 2 bar set. All of our fly cutter products including the bars and cutter bodies are plated with clear zinc for corrosion resistance and are cryogenically treated (prior to manufacturing) for stability and to reduce vibration. We sincerely hope that you can leave us a. Suburban Tool Fly Cutter as good as Surface Grinder? The item “Suburban Tool Fly Cutter Body and 2 Bar Set (5 and 7.5 BARS) SEE VIDEO” is in sale since Monday, December 7, 2020. This item is in the category “Business & Industrial\CNC, Metalworking & Manufacturing\Metalworking Supplies\Milling Cutters”. The seller is “mvpmachine” and is located in Fraser, Michigan. This item can be shipped worldwide.

• Quantity: 1
• Country/Region of Manufacture: United States
• MPN: FCS-SET0507
• Brand: Suburban Tool
• UPC: Does not apply
• Model: Suburban Tool Fly Cutter Set

]]> https://cuttersettool.com/2020/12/12/suburban-tool-fly-cutter-body-and-2-bar-set-5-and-7-5-bars-see-video/feed/ 0