Parking Sensor Distance Control Hole Cutter Tool Set 17mm 32mm With Drill Bit
January 26, 2019
Laser Tools New Releases. Allen Hex Torx Key Sets. Spanners & Wrench Tools. Workwear Clothing & Shoes. Grips Pliers & Wrenches. Drill Bits & Adaptors. Home & Leisure Equipment. Add to Favourite Sellers. Sign up to Newsletter. Parking Sensor Distance Control Hole Cutter Tool Set 17mm – 32mm With Drill Bit. Hole cutter set for parking distance control sensors for fitting and replacing Additional Information EN DE For re-fitting parking sensors after accident damage Hole cutter sizes: Hole cutter sizes: 17, 18, 18.2, 19, 20, 22.5, 24, 26, 26.7, 32mm Cuts up to 5mm plastic Includes 5/16″ HSS Drill Bit F&###xC3;&###xBC;r die Montage von Abstandssensoren nach Unfallsch&###xC3;&###xA4;den Lochschneider-Gr&###xC3;&###xB6;&###xC3;&###x178;en: Lochschneider-Gr&###xC3;&###xB6;&###xC3;&###x178;en: 32 > 26&###xA0;mm, 26,7 > 24&###xA0;mm, 22,5 > 18,2&###xA0;mm, 20 > 18&###xA0;mm, 19 > 17&###xA0;mm Schneidet bis 5&###xA0;mm starken Kunststoff Inklusive 5/16″-HSS-Bohrer Professional bodyshops know and trust Power-TEC products and this new parking distance sensor hole cutter set&###xA0;lets you cut dimensionally accurate holes cleanly and quickly when refitting the parking sensors after accident damage. The operation couldn&###xE2;&###x20AC;&###x2122;t be easier; drill the pilot hole in the new panel (5/16 HSS drill bit included), then choose the correct combination of die and cutter punch from the set (ten hole sizes available). Assemble with the die behind the panel and the cutter punch on the outer face then tighten the nut on the force screw with a 12mm socket and within seconds the hole is cut, leaving a clean finished edge on the outer surface of the panel. Up to 5 mm plastic can be cut and the following hole sizes are accommodated in the set: 32, 26.7, 26, 24, 22.5, 20, 19, 18.2, 18, and 17mm. Part of the Power-TEC range of parking sensor kits which includes 92468 (18.2mm cutter plus clamps to keep the sensor brackets in place while the mounting adhesive sets) and 92471 which includes&###xA0; 18.2, 18.4 and 26mm cutters plus three sizes of clamp. Professional results every time whenever you need to cut holes for parking distance sensors; the set is available now from your Power-TEC supplier. 50 Years experience of repairing vehicles we feel well qualified to trade within the automotive sector as a supplier of tools & equipment. This is where our business has the advantage over our competitors, we carry a large stock for immediate supply or the promise that non stock items can be dispatched within 48hrs. With having our own up to date workshops we have a wealth of experience & skill to advise on any questions we are asked , from technical data to how the items works. If we cannot answer the query we have many contacts and our 50 years experience in the business to find out the correct answers for you. You can add these instructions on to your checkout if preferred, in the Additional check out instructions section. Once goods have been delivered to you they will be held at your own risk and we will not be liable for their loss or destruction. We shall have no liability to you for any failure to deliver goods you have ordered or any delay in doing so or for any damage or defect to goods delivered that is caused by any event or circumstance beyond our reasonable control including, without limitation, strikes, lock-outs and other industrial disputes, breakdown of systems or network access, flood, fire, explosion or accident. Our acceptance of your order brings into existence a legally binding contract between us. Price 2.1 The prices payable for goods that you order are as set out in our website. You do not need to give us any reason for cancelling your contract. 3.2 To cancel your contract you must notify us in writing. 3.3 If you have received the goods before you cancel your contract then you must send the goods back to our contact address at your own cost and risk. Cancellation by us 4.1 We reserve the right to cancel the contract between us if: 4.1.1 we have insufficient stock to deliver the goods you have ordered; 4.1.2 we do not deliver to your area; or 4.1.3 one or more of the goods you ordered was listed at an incorrect price due to a typographical error or an error in the pricing information received by us from our suppliers. We will not be obliged to offer any additional compensation for disappointment suffered. 6.2 If you do not receive goods ordered by you within 10 days of the date on which you ordered them, we shall have no liability to you unless you notify us in writing at our contact address of the problem within 15 days of the date on which you ordered the goods. The importation or exportation of certain of our goods to you may be prohibited by certain national laws. 6.7 Notwithstanding the foregoing, nothing in these terms and conditions is intended to limit any rights you might have as a consumer under applicable local law or other statutory rights that may not be excluded nor in any way to exclude or limit our liability to you for any death or personal injury resulting from our negligence 7. Notices 7.1 Unless otherwise expressly stated in these terms and conditions, all notices from you to us must be in writing and sent to our contact address at YOUR ADDRESS PLEASE and all notices from us to you will be displayed on our website from to time. Events beyond our control 8.1 We shall have no liability to you for any failure to deliver goods you have ordered or any delay in doing so or for any damage or defect to goods delivered that is caused by any event or circumstance beyond our reasonable control including, without limitation, strikes, lock-outs and other industrial disputes, breakdown of systems or network access, flood, fire, explosion or accident. Invalidity 9.1 If any part of these terms and conditions is unenforceable (including any provision in which we ex-clude our liability to you) the enforceability of any other part of these conditions will not be affected. Privacy 10.1 You acknowledge and agree to be bound by the terms of our privacy policy. Third party rights 11.1 Except for our affiliates, directors, employees or representatives, a person who is not a party to this agreement has no right under the UK Contracts (Rights of Third Parties) Act 1999 to enforce any term of this agreement but this does not affect any right or remedy of a third party that exists or is available apart from that Act. Governing law 12.1 The contract between us shall be governed by and interpreted in accordance with English law and the English courts shall have jurisdiction to resolve any disputes between us. Nothing said by any sales person on our behalf should be understood as a variation of these terms and conditions or as an authorised representation about the nature or quality of any goods offered for sale by us. Save for fraud or fraudulent misrepresentation, we shall have no liability for any such representation being untrue or misleading. Procedure to request an item return: 1. You may be asked to sign in. Next to your listing, select Return this item from the pull-down menu. The “Return an item” form appears. View more great items. This listing is currently undergoing maintenance, we apologise for any inconvenience caused. The item “Parking Sensor Distance Control Hole Cutter Tool Set 17mm 32mm With Drill Bit” is in sale since Monday, July 31, 2017. This item is in the category “Vehicle Parts & Accessories\Car Accessories\Safety\Other Safety”. The seller is “hardwick1982_on” and is located in Sutton-in-Ashfield. This item can be shipped worldwide.
- Manufacturer Part Number: Does Not Apply
- Brand: Unbranded